Acidmods

Console Modding------ ( Here you can talk about your favorite Consoles ) => PSP's => Topic started by: aszure on March 17, 2009, 05:03:55 PM

Title: backlight connector broken
Post by: aszure on March 17, 2009, 05:03:55 PM

(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Fimg23.imageshack.us%2Fimg23%2F7223%2Fp3170083n.jpg&hash=1bfe1c1a7af8350740b34e680735f9b221db9052)

is there any for me to fix it

or do i have to buy a new motherboard?
Title: Re: backlight connector broken
Post by: juust0_ on March 17, 2009, 11:02:05 PM
You could try soldering the ribbon to those 4 pins.
Title: Re: backlight connector broken
Post by: rgarjr on March 17, 2009, 11:25:08 PM
U can try soldering the FFC cable to those small ass pins, but good luck. 
Title: Re: backlight connector broken
Post by: aszure on March 18, 2009, 09:20:49 AM
actually theres 8 pins, 4 on top and 4 on bottom

im not sure where to sodler it tho
Title: Re: backlight connector broken
Post by: krazyone2006 on March 18, 2009, 10:32:27 AM
did you try using a little piece of paper on as a wedge to hold it in cause if its like the phats just the bottom pins have to keep connection
Title: Re: backlight connector broken
Post by: aszure on March 18, 2009, 03:44:30 PM
yes i used a wedge to make the backlight connector connect properly, i had to make the connector on the backlight to tilt up slightly . and thats how i broke the connector in the first place

would i have to solder them all or do i have to pick the appropriate 2 pins to solder to the connector?
Title: Re: backlight connector broken
Post by: aszure on April 11, 2009, 06:49:01 PM
anyone?

Title: Re: backlight connector broken
Post by: thearkman2009 on April 11, 2009, 06:57:39 PM
If you get it in and can hold it there for a minute, use one of the black felt-looking tape pieces that hold the speaker wires to the mother board, to hold the ribbon cable in place.  They pretty sticky.  I use them for just about everything.
Title: Re: backlight connector broken
Post by: mastapsp on April 12, 2009, 02:23:37 AM
 :rofl:
haha that is funny, i have had some problems that have caused me time and money but that is bad
just experiment and post your work
Title: Re: backlight connector broken
Post by: frankjasso on April 29, 2009, 11:40:56 PM
one time that happened to me and i just put some tap and something under the tap pressing the little pings and that should work find
Title: Re: backlight connector broken
Post by: W-Gaming5 on April 30, 2009, 09:30:03 PM
 :censored: :censored: :censored: :censored: :censored: :censored: :censored: :censored:
Title: Re: backlight connector broken
Post by: OnyxDragon on May 11, 2009, 07:55:18 AM
i stuck blutack there to stabilize the connector in position and used folded paper to wedge it there. works!
Title: Re: backlight connector broken
Post by: maelo0525 on May 29, 2009, 12:37:31 PM
I had the same Problem all i did was solderd to cables to outer pins and then solderd them to the conector tape to the backlight and it worked fine. :drunk:
SimplePortal 2.3.5 © 2008-2012, SimplePortal