Author Topic: DualShock 4 Controller PCB scans  (Read 79163 times)

Offline kempie1234

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #90 on: February 23, 2017, 08:44:24 AM »
Thanx for the reply!

It works great with the new 150k 0402 resistor!

Thnx!

Offline RDC

  • Acid Modder
  • *
  • Posts: 723
  • Post quality +78/-2
  • Gender: Male
  • The CGnome Project
Re: DualShock 4 Controller PCB scans
« Reply #91 on: February 23, 2017, 02:37:24 PM »
Welcome.
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline saboteur_vn

  • Guppy
  • *
  • Posts: 2
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #92 on: May 11, 2017, 02:51:08 AM »
In the left circle, the 2 vertical components are Resistors, 10k, 0402. The horizontal one is also a Resistor, 0ohm, 0603.

In the right circle, the top component is an NPN Transistor, marking is KKB and you'll have to hunt for it. The bottom one is a Resistor, 1M, 0402.

Hi everybody. I have the same trouble(right circle) - losed this npn transistor(pcb is jdm-001). But i cant find any "KKB" smd transistor  :cry2: :cry2: :cry2: (i founde only XC9235C2BDM - dc-dc converter KKB marking,but it 5 pins - wrong way)

Guys,maybe somebody knows what transistor should i order for replacement this ?  :help:

« Last Edit: May 11, 2017, 03:12:03 AM by saboteur_vn »

Offline RDC

  • Acid Modder
  • *
  • Posts: 723
  • Post quality +78/-2
  • Gender: Male
  • The CGnome Project
Re: DualShock 4 Controller PCB scans
« Reply #93 on: May 11, 2017, 04:35:53 AM »
It's just a general purpose NPN for turning on one of the 3 LEDs for the Light bar. The other 2 are on the other side of the board in roughly the same location.

It's the SC70 or SOT323 package, and the pinout is 1 - Base, 2 - Emitter, 3 - Collector. Pretty much anything would work in there as it's just a switch, so the PMSS3904 or BC847 or really any of a huge number of NPN would work fine.
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline ucsd8121

  • Guppy
  • *
  • Posts: 1
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #94 on: May 11, 2017, 04:48:00 PM »
Hi guys,

Total newb here trying to put the guts of DS4 into my Madcatz TE2+ to make it wireless...  I read over all of the posts on this thread, but I am still confused. 

My DS4 PCB is JDM-040.  I'm still confused about the wiring for L2 and R2 buttons.  So how does the wiring go in order to make those button functional?  My understanding is from 3.2v connect 10k resistor then wire that to L2 which then gets wired to one of the leads on the button, then 2L which gets wired to the other lead for the button for L2? 

so from DS4 PCB, lead for 3.2v --> wire --> 10K resistor --> wire --> L2 on PCB  --> wire --> L2 button lead, and then other L2 button lead --> wire --> 2L on PCB.  Is this correct?

Any help will be so much appreciated.

Offline RDC

  • Acid Modder
  • *
  • Posts: 723
  • Post quality +78/-2
  • Gender: Male
  • The CGnome Project
Re: DualShock 4 Controller PCB scans
« Reply #95 on: May 12, 2017, 12:34:59 AM »
Depends what you're definition of functional is. Those buttons are Analog, but if all you want is for them to be is Digital (on/off) like an arcade stick button, then just wire them up how you're thinking they go there, as that is correct.

3.2v--(10k)--L2

L2---New L2 button (one side)
2L---New L2 button (other side)

Then just repeat the same thing with another 10k and R2/2R for the new R2 button.

Also remember that L1, R1, L3 and R3 all use 3.2v as the Common. All other buttons use Ground for the Common.

« Last Edit: June 24, 2017, 12:43:54 AM by RDC »
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline saboteur_vn

  • Guppy
  • *
  • Posts: 2
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #96 on: May 12, 2017, 01:53:05 AM »
It's just a general purpose NPN for turning on one of the 3 LEDs for the Light bar. The other 2 are on the other side of the board in roughly the same location.

It's the SC70 or SOT323 package, and the pinout is 1 - Base, 2 - Emitter, 3 - Collector. Pretty much anything would work in there as it's just a switch, so the PMSS3904 or BC847 or really any of a huge number of NPN would work fine.



Great. Thank you veery much. Yes, leds work then i turn  on or charge the pad. Maybe not all colors are work - Orange wotking. Blue (and white) - are not,
it seems.

Offline RDC

  • Acid Modder
  • *
  • Posts: 723
  • Post quality +78/-2
  • Gender: Male
  • The CGnome Project
Re: DualShock 4 Controller PCB scans
« Reply #97 on: May 12, 2017, 07:48:05 AM »
Yep, that one is for the Blue LED in there, so any color needing Blue would not work, so Blue, White, Violet, etc.
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline turnkey

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #98 on: May 23, 2017, 07:32:09 AM »
Does anyone make a remap board that has the 2R / 2L for the JDM-001?

Offline Zero-X

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #99 on: July 06, 2017, 09:24:09 AM »
Hello everybody,

My problem is that my "options" button is not working.
When i opened the controller i could see a white thing around the button on the electronic plate, like "powder".
I cleaned it up, but i cannot see what is wrong.
Can someone tell me what happened here?

It is the JDM-011 version.

Sorry for my english, i am from germany.




« Last Edit: July 06, 2017, 09:48:47 AM by Zero-X »

Offline RDC

  • Acid Modder
  • *
  • Posts: 723
  • Post quality +78/-2
  • Gender: Male
  • The CGnome Project
Re: DualShock 4 Controller PCB scans
« Reply #100 on: July 06, 2017, 05:58:45 PM »
That powder was probably just left over from the board when it was cleaned and does not hurt anything, unless you spilled something on it?

Does the button still click when it it pressed? If not, then it is probably bad. They can wear out or fail early and still click though. That is the first and easiest place to start, either replace it or use a DMM and see if it is working correctly.

Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline Zero-X

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #101 on: July 07, 2017, 12:48:01 AM »
Thank you for your answer.

Yes, the button does click when pressed.
I yoused a dmm, between this two points, and pressed the button and it still works.
It seems that the button himself is working, but the signal is anywhere interrupted.

 


Thank you in Advance.


Offline RDC

  • Acid Modder
  • *
  • Posts: 723
  • Post quality +78/-2
  • Gender: Male
  • The CGnome Project
Re: DualShock 4 Controller PCB scans
« Reply #102 on: July 07, 2017, 01:10:23 AM »
You can trace it out and see if there is a break, but then it goes right under MCU where you can not really check that connection. If the trace is good, then either the BGA solder joint at the MCU is bad or the MCU is bad.





Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline Zero-X

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #103 on: July 07, 2017, 01:38:10 AM »
Thank you, i will check it later.

1.Is the white marked line that trace i have to check?
2.Do you know if there is a resistor or anything else between the button and MCU?

« Last Edit: July 07, 2017, 01:48:13 AM by Zero-X »

Offline RDC

  • Acid Modder
  • *
  • Posts: 723
  • Post quality +78/-2
  • Gender: Male
  • The CGnome Project
Re: DualShock 4 Controller PCB scans
« Reply #104 on: July 07, 2017, 01:44:16 AM »
Yes
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline marsel

  • Guppy
  • *
  • Posts: 2
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #105 on: July 13, 2017, 06:42:38 PM »
Hi guys, can someone help me? sorry if my question not correctly about modding but i have problem with my ds4 JDM-011. right stick always to the lower left if playing game.


Offline RDC

  • Acid Modder
  • *
  • Posts: 723
  • Post quality +78/-2
  • Gender: Male
  • The CGnome Project
Re: DualShock 4 Controller PCB scans
« Reply #106 on: July 13, 2017, 08:22:39 PM »
Well for starters, that's a pic of the bottom of where the Left stick goes, so if you do have an issue with the Right one that's not going to be of much help. If the issue is with that Left stick, then there are either shorts, messed up traces or pulled plating in some of the holes there. No way to tell from that pic exactly what the issue is as it's too blurry.
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline marsel

  • Guppy
  • *
  • Posts: 2
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #107 on: July 14, 2017, 12:22:22 AM »
Well for starters, that's a pic of the bottom of where the Left stick goes, so if you do have an issue with the Right one that's not going to be of much help. If the issue is with that Left stick, then there are either shorts, messed up traces or pulled plating in some of the holes there. No way to tell from that pic exactly what the issue is as it's too blurry.
sry its new foto, i had change my analog ds4 but no diffrent. i try to peel the line for check if there is a break but i am confused now to fix it. sry my english is bad, i used translate google




Offline RDC

  • Acid Modder
  • *
  • Posts: 723
  • Post quality +78/-2
  • Gender: Male
  • The CGnome Project
Re: DualShock 4 Controller PCB scans
« Reply #108 on: July 15, 2017, 03:12:55 PM »
You'll need a meter to find the break or short. Both sticks should measure pretty much the same, so you can use the other one for comparison.
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline JungleThing

  • Guppy
  • *
  • Posts: 1
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: DualShock 4 Controller PCB scans
« Reply #109 on: August 10, 2017, 07:26:28 PM »
Hey im wondering if you could or if someone could upload a zoomed in picture of the jdm 040 circuit board.  I'm trying to see what components are on the left side next to the left joysticks. I say this because I think I'm missing that piece.  Not sure what the component is or what size but I'm thinking it's a diode.  So if you all could please assist me with locating that part then I can modify my circuit board as well. Thank you all if you can assist.
Also I can show you a picture of what I'm missing.

« Last Edit: August 10, 2017, 07:29:38 PM by JungleThing »

Offline RDC

  • Acid Modder
  • *
  • Posts: 723
  • Post quality +78/-2
  • Gender: Male
  • The CGnome Project
Re: DualShock 4 Controller PCB scans
« Reply #110 on: August 10, 2017, 08:26:58 PM »
It's a diode for the rumble motor. Cathode side is denoted by the round mark there. The same circuit is on the right side of the board for the other motor.
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.