Author Topic: 3-Mode ROL color changer  (Read 8246 times)

Offline drummerdude

  • BST BAN
  • ♥ Poker Champ ♠♣
  • *
  • Posts: 237
  • Post quality +11/-5
  • Gender: Male
  • Acidmods User
3-Mode ROL color changer
« on: November 27, 2011, 02:45:46 PM »
3-mode ROL color changer



Introduction
In this guide, I will show you how to install the 3-mode ROL color changer into your xbox 360 controller.

3-Mode ROL Color Changer

Parts Needed

[admin] if files go down the hex files will always be stored at acidmods.com here [/admin]


Tools Needed
  • Solder Iron
  • tweezers


Difficulty rating: 4/5


Average Time to Complete: 30mins-1hour


Step By Step Tutorial
1. Take apart your controller using this video
Xbox 360 Wireless controller dissasembly video tutorial





2. Once the controller is dismantled, hot glue a small piece of breadboard underneath the controller. We will be using this to solder your leds to. It needs to be in the right spot or else the controller case will get in the way.



3. Next solder one 1k ohm resistors to each of the sides of the breadboard, since there are 2 different led colors we are  using.


4. Now You need to hot glue the chip in dead bug position and make sure the notch is facing away from the controller. Then bend the resistors to the top of the controller and solder 1 resistor to pin 7 and the other one to pin 6. Also solder pin 3 to the sync button.


5. Now time to solder the ground and the power. Pin 1 needs to be soldered to the power, and pin 8 needs to be soldered to the ground.


6. Now we need to remove the leds on the controller. Here's how I do it. First get a big blob of solder on your iron and put it up to the led. Make sure the solder is touching both contacts of the led. Then just lightly push the led off, and it should come smoothly off.


7. Now the harder part! Now solder a wire to one of the 0603 leds. Solder it to which ever side it is necessary for that controller. Solder it to the positive for matrix controllers, and the ground for CG controllers. Now I recommend putting a small piece of electrical tape over the contact on the controller that isn't being used, So that way the leds don't touch it.  Now solder the led on to the contact. But put it like only half way on, so that we have room for another led.



8. Now once the led is soldered to the pad, loop the wire back underneath the controller and solder it to one of the sides of the breadboard. Make sure you solder all the blue leds to one side, and the red leds to the other. So remember which side is which.



9. Now solder another wire to the color led we didn't do yet. Then solder it to the other half of the pad. Then loop the wire around and solder it to the other side of the breadboard. Now repeat this process for all of the led contacts!



10. You might need to trim the button pad a little bit so that the pad doesn't cover the leds.



11. The controller should look like this when you finish. Now just put the controller back together and you're finished!



FAQ/ Troubleshooting
  • -when using this mod on the CG controller, I noticed the leds are a little dim when they are supposed to be off, but it doesn't affect the colors that much
« Last Edit: November 21, 2012, 02:51:26 PM by Modded Matt »

"I'm not a very tall person, however I show self-confidence of a bigger person"

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: 3-Mode ROL color changer
« Reply #1 on: December 03, 2011, 06:17:38 PM »
The tutorial is coming along great. are you adding the hex code? just wondering, or if its in open soucre? nice job and congrates again for joining and showing off your work in the Stand Out Competition

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline drummerdude

  • BST BAN
  • ♥ Poker Champ ♠♣
  • *
  • Posts: 237
  • Post quality +11/-5
  • Gender: Male
  • Acidmods User
Re: 3-Mode ROL color changer
« Reply #2 on: December 03, 2011, 06:48:27 PM »
ill add the code when i finish the tut sometime soon hopefully

"I'm not a very tall person, however I show self-confidence of a bigger person"

Offline 3D0kassiah

  • Acid Modder
  • *
  • Posts: 809
  • Post quality +19/-2
  • Gender: Male
  • Acidmods User
Re: 3-Mode ROL color changer
« Reply #3 on: December 26, 2011, 12:58:46 PM »
niiiice
please share the hex when finished
bought 2 cg controllers gonna take another crack at led mods
Tracey: f off Rodent
rodent:i would of flew it to bill gates and shoved it up his a$$

Offline crazy-modder

  • Research & Development
  • Acid Modder
  • *
  • Posts: 854
  • Post quality +34/-2
  • Gender: Male
Re: 3-Mode ROL color changer
« Reply #4 on: December 26, 2011, 05:12:45 PM »
looks like a pretty sweet code dude, im gonna have to try it out once you release it. Great job and keep up the good work.

Offline drummerdude

  • BST BAN
  • ♥ Poker Champ ♠♣
  • *
  • Posts: 237
  • Post quality +11/-5
  • Gender: Male
  • Acidmods User
Re: 3-Mode ROL color changer
« Reply #5 on: December 26, 2011, 07:55:24 PM »
Thanks! I appreciate you guys checkin out my work! Its almost done!

"I'm not a very tall person, however I show self-confidence of a bigger person"

Offline Famas

  • Granny Spanker
  • *
  • Posts: 403
  • Post quality +1/-8
  • Acidmods User
Re: 3-Mode ROL color changer
« Reply #6 on: November 21, 2012, 11:51:25 AM »
sorry to dig up old posts but i really want to do this does anyone have this code or a code like this please ?

Offline rafaliyo86

  • Acid Modder
  • *
  • Posts: 569
  • Post quality +12/-1
  • Gender: Male
  • Acidmods User
Re: 3-Mode ROL color changer
« Reply #7 on: November 21, 2012, 12:38:40 PM »
sorry to dig up old posts but i really want to do this does anyone have this code or a code like this please ?

The codes are in parts needed

Offline snowcolt17

  • Moderator
  • Acid Modder
  • *
  • Posts: 552
  • Post quality +16/-1
  • Gender: Male
  • If all else fails, reflow it
Re: 3-Mode ROL color changer
« Reply #8 on: November 21, 2012, 12:39:11 PM »
sorry to dig up old posts but i really want to do this does anyone have this code or a code like this please ?

yea drummerdude, keep the links active. lol jk

i think i know what happened.. if a file on rapidshare hasnt been used in 45 days it deletes it.


Offline drummerdude

  • BST BAN
  • ♥ Poker Champ ♠♣
  • *
  • Posts: 237
  • Post quality +11/-5
  • Gender: Male
  • Acidmods User
Re: 3-Mode ROL color changer
« Reply #9 on: November 21, 2012, 12:44:25 PM »
I noticed that. I tried to put them as an attachment, but it wasnt working out. I dont even think it worked out to begin with. lol. I dont really know how to host codes. If someone wants to help me, I can email you the codes and you can host them?

"I'm not a very tall person, however I show self-confidence of a bigger person"

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: 3-Mode ROL color changer
« Reply #10 on: November 21, 2012, 12:47:15 PM »
The attachment folder is full. Robin has to go in and allocate more space.

email them to me and I will host them on the acidmods server.

my email is:

moddedmatt@the name of this site.com
« Last Edit: November 21, 2012, 12:48:24 PM by Modded Matt »

Offline Famas

  • Granny Spanker
  • *
  • Posts: 403
  • Post quality +1/-8
  • Acidmods User
Re: 3-Mode ROL color changer
« Reply #11 on: November 21, 2012, 12:51:08 PM »
looking forward to installing this! cheers matt

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: 3-Mode ROL color changer
« Reply #12 on: November 21, 2012, 02:49:35 PM »
Here are the hex files: link

he did not send the schematics

Offline Famas

  • Granny Spanker
  • *
  • Posts: 403
  • Post quality +1/-8
  • Acidmods User
Re: 3-Mode ROL color changer
« Reply #13 on: November 27, 2012, 12:31:44 PM »
just wondering what type of 0603 leds xbox 360 controllers need i.e what the foward voltage needs to be and what the current needs to be :) http://uk.farnell.com/jsp/search/browse.jsp?N=2031+204192&Ntk=gensearch&Ntt=0603+led&Ntx=mode+matchallpartial

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal