Author Topic: backlight connector broken  (Read 5449 times)

Offline aszure

  • Guppy
  • *
  • Posts: 5
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
backlight connector broken
« on: March 17, 2009, 05:03:55 PM »



is there any for me to fix it

or do i have to buy a new motherboard?

Offline juust0_

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 52
  • Post quality +0/-0
  • Gender: Male
  • ;woot modder
Re: backlight connector broken
« Reply #1 on: March 17, 2009, 11:02:05 PM »
You could try soldering the ribbon to those 4 pins.
PSP History

4 PSP Phats
1 Silver Slim

Offline rgarjr

  • Ω Allumnist Ω
  • *
  • Posts: 131
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: backlight connector broken
« Reply #2 on: March 17, 2009, 11:25:08 PM »
U can try soldering the FFC cable to those small ass pins, but good luck. 

Offline aszure

  • Guppy
  • *
  • Posts: 5
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: backlight connector broken
« Reply #3 on: March 18, 2009, 09:20:49 AM »
actually theres 8 pins, 4 on top and 4 on bottom

im not sure where to sodler it tho

Offline krazyone2006

  • PoM PuFFs??
  • Registered BST
  • Granny Spanker
  • *
  • Posts: 385
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: backlight connector broken
« Reply #4 on: March 18, 2009, 10:32:27 AM »
did you try using a little piece of paper on as a wedge to hold it in cause if its like the phats just the bottom pins have to keep connection

Offline aszure

  • Guppy
  • *
  • Posts: 5
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: backlight connector broken
« Reply #5 on: March 18, 2009, 03:44:30 PM »
yes i used a wedge to make the backlight connector connect properly, i had to make the connector on the backlight to tilt up slightly . and thats how i broke the connector in the first place

would i have to solder them all or do i have to pick the appropriate 2 pins to solder to the connector?

Offline aszure

  • Guppy
  • *
  • Posts: 5
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: backlight connector broken
« Reply #6 on: April 11, 2009, 06:49:01 PM »
anyone?


Offline thearkman2009

  • Registered BST
  • E = MC²
  • *
  • Posts: 332
  • Post quality +2/-0
  • Gender: Male
  • Designing Innovative Mods
    • SteelROMs
Re: backlight connector broken
« Reply #7 on: April 11, 2009, 06:57:39 PM »
If you get it in and can hold it there for a minute, use one of the black felt-looking tape pieces that hold the speaker wires to the mother board, to hold the ribbon cable in place.  They pretty sticky.  I use them for just about everything.

Offline mastapsp

  • Ω Allumnist Ω
  • *
  • Posts: 102
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: backlight connector broken
« Reply #8 on: April 12, 2009, 02:23:37 AM »
 :rofl:
haha that is funny, i have had some problems that have caused me time and money but that is bad
just experiment and post your work

Offline frankjasso

  • Guppy
  • *
  • Posts: 7
  • Post quality +0/-0
  • Gender: Male
  • FrankJasso
Re: backlight connector broken
« Reply #9 on: April 29, 2009, 11:40:56 PM »
one time that happened to me and i just put some tap and something under the tap pressing the little pings and that should work find

Offline W-Gaming5

  • Millennium Poster
  • *
  • Posts: 1129
  • Post quality +1/-0
  • Gender: Male
Re: backlight connector broken
« Reply #10 on: April 30, 2009, 09:30:03 PM »
 :censored: :censored: :censored: :censored: :censored: :censored: :censored: :censored:
« Last Edit: July 29, 2012, 11:22:52 AM by W-Gaming5 »
:censored:

Offline OnyxDragon

  • Guppy
  • *
  • Posts: 1
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: backlight connector broken
« Reply #11 on: May 11, 2009, 07:55:18 AM »
i stuck blutack there to stabilize the connector in position and used folded paper to wedge it there. works!

Offline maelo0525

  • Guppy
  • *
  • Posts: 7
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: backlight connector broken
« Reply #12 on: May 29, 2009, 12:37:31 PM »
I had the same Problem all i did was solderd to cables to outer pins and then solderd them to the conector tape to the backlight and it worked fine. :drunk:

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal